How do I uninstall DTT AverMedia driver for USB stick? I installed a wrong driver on OpenPli 4.0 with IPTV.

Probably the best is to just reflash the image clean, as it really depends of the installation / ipk that was used during installation. Easier and faster is just reinstall the image clean.

Admin

Ok, I used ipk install for the driver. I have see that OpenPli 4.0 wIPTV v22 don't work with AverMedia dvb-t AF9015 driver.

My DM800HDse is a Sunray box with BSBE-801A tuner and usb Manhattan dvb-t stick and for years I use Nemesis 2.6 110r0. Now I have NC3 sim. I reinstall OpenPli 4.0 and now the yellow bar goes only the half way and stick there. I use the HTTP method and always finish the installation with the bootloader SSL84j. Iam totally lost know and was thinking about to put in my old sim 2.10 and start from there.

If you know something about this problem that the yellow bar goes just the half way in startup I appreciate some instruction.

Pall64,

Why are you doing all this ?

Just flash the OpenPLi 4.0 IPTV v22 image, that's all, then on the JAM install the AF9015 driver as shown on the topic below,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=10030#Post10030

I don't understand why you try to flash ssl, etc after the image, that already has it inside, you are only corrupting the image. So just flash the image and do the normal setup as you would do with any image.

Admin

I have misunderstood what Johnny B. said in his post " Re: No Ca or image failed ! Help ! [Re: pazitush]" ..... "If you want later to upload another Japhar image file, you can do it with your browser.
Upload the Japhar image file, do not reset, upload the ssl84J boot loader.
Restart your receiver etc...."

I understood that, every time I upload a new Japhar image I should upload the ssl84j after the image. But that was wrong.

Know I have upload OpenPli 4.0 wIPTV and it works, but not with the beautiful country startup picture just a black dreambox.

When I installed the usb driver for dvb-t I thougt I choose a wrong one "Avermedia Volar Black HD 850 (AF9015) because it dit´t work so well. There is no one without "HD" in Jam now, just in your post. Maybe it does't matter, but I had constantly freesing picture and a green screen.

If you have no boot logo on the TV, turn off the box and turn on, it should be then OK. It's important that you get the right bootlogo if you want the box to work 100% flawlessly.

Concerning the SD/HD for DVB-T Dongles, in fact there is no importance, as the stream is sent to the DM receiver that then handles the MPEG2 or the MPEG4/H264. So you can use a dongle labelled SD, to watch HD channels, as the job is not done by the dongle but by the DM Box / PC etc.

Admin

P.S.: Be careful as well, as there is the OpenPLi IPTV support with drivers, and there is the old images OE1.6 drivers for DVB-T just a little before in the list. So be sure you install the right drivers and not the old ones. Probably this is what happened, and reason why these doesn't work as these are for older images from 2010-2011.

In the second reboot I have now this beautiful freesing country boot logo picture on the screen. Know I will do some experiment with my usb dvb-t stick. Thank you for your quick reply.

I have upload new image Japhar OpenPli 4.0 wIPTV v22 and MastaG OpenPli 4.0 wIPTV v21 and both works fine until I upload DVB-t AF9015 then everything goes wrong f.ex. IPTV stop working. It is wery strange I can search and find channels on dvbt but not watching them, tune failed and sometimes it freeze.
Another thing is the timezone I live in GMT area when time is 8.00 it shows 9.00 it is very strange. When I change the time zone from -1 to GMT it jumps two hours.
I must have dvb-t and I know some user "kikan" had similar problems.

Hello,

Are you sure you used the right driver ? Please tell us the exact driver you installed, and from where. Was it from the OpenPLi 4.0 Support section on the JAM 5.x ? That's the only one that will work.

Remember also that if the IPTV/DVB doesn't work, it's mostly because of a false boot, so be sure you had the bootlogo when the box started.

TS

Hi, on the satellite and IPTV site, everything works perfectly, no not the timezone, still working on that.

After I install drivers AF9015 for my USB dongle (have also tested AF9035 without progress) everything goes wrong.

I bought two Japhar NC3 for DM800se and one for DM8000. I tried to swap sim for DM800se to check if it was the sim but with the same problems so it not the sim NC3.

First I try to use OpenPli 4.0 wIPTV v22 and then Blackhole didn't make differens.

I took some pictures so you can see the process.

Here is picture of USB dongle for terrestial antenna.

We need the PID:VID to know for sure which Chipset there is inside, and if it's supported by the Linux drivers,

Admin

How can I get these pid and vid?

You insert the DVB-T Dongle on your PC and you will have such details on the configuration of your PC hardware,

Admin

Hi, here are few pictures...

These are all the VID:PID supported on the images,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=10334#Post10334

I don't find any 15A4:9016

Admin

Are you kidding me? These are only 4 of 11 that are in Jam 5.3. In Jam there are at least three AF drivers AF9005, AF9015 and AF9035. Why do you have them there if you don't support them?

Look at the link I gave you, there is MANY MANY more, as the AF9015 is only the chipset and MANY MANY Dongles are based on the exact same chipset, so you can see every line on the link is one dongle with it's VID:PID,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=10334#Post10334

On my actual calculation there is at least 111 dongles supported...

Admin

VID:2040 PID:C090
VID:2040 PID:C080
VID:2040 PID:C010
VID:2040 PID:C000
VID:2040 PID:B990
VID:2040 PID:B980
VID:2040 PID:B910
VID:2040 PID:B900
VID:187F PID:0301
VID:187F PID:0202
VID:2040 PID:5590
VID:2040 PID:5580
VID:2040 PID:5530
VID:2040 PID:5520
VID:2040 PID:5510
VID:2040 PID:5500
VID:2040 PID:2019
VID:2040 PID:2011
VID:2040 PID:2010
VID:2040 PID:200A
VID:2040 PID:2009
VID:2040 PID:2000
VID:2040 PID:1801
VID:2040 PID:1800
VID:2040 PID:1700
VID:187F PID:0300
VID:187F PID:0201
VID:187F PID:0200
VID:187F PID:0100
VID:187F PID:0010
VID:14F7 PID:0004
VID:0FD9 PID:0011
VID:10B8 PID:1FA0
VID:2304 PID:0248
VID:2304 PID:0245
VID:1E59 PID:0002
VID:1554 PID:5010
VID:10B8 PID:1F90
VID:10B8 PID:1F98
VID:0CCD PID:00AB
VID:10B8 PID:1E80
VID:2013 PID:0248
VID:2013 PID:0245
VID:2304 PID:0243
VID:1164 PID:1E8C
VID:1164 PID:1EFC
VID:0CCD PID:10A1
VID:0CCD PID:10A0
VID:0413 PID:60F6
VID:0FD9 PID:0020
VID:0FD9 PID:0021
VID:1164 PID:0871
VID:2040 PID:B210
VID:2040 PID:B200
VID:1164 PID:2EDC
VID:1415 PID:0003
VID:0CCD PID:0081
VID:0CCD PID:0062
VID:2304 PID:023B
VID:2304 PID:023A
VID:0B05 PID:1736
VID:1164 PID:1F08
VID:1044 PID:7002
VID:2040 PID:8400
VID:2040 PID:5200
VID:0413 PID:6F01
VID:0CCD PID:0078
VID:0CCD PID:0060
VID:1164 PID:1EDC
VID:2304 PID:0237
VID:2304 PID:0236
VID:2304 PID:022E
VID:0CCD PID:0058
VID:2040 PID:7080
VID:2040 PID:7070
VID:0B05 PID:173F
VID:0B05 PID:171F
VID:05D8 PID:810F
VID:1044 PID:7001
VID:07CA PID:B568
VID:185B PID:1E80
VID:2304 PID:0229
VID:10B8 PID:1EBE
VID:2304 PID:0228
VID:10B8 PID:1EBC
VID:10B8 PID:1EF0
VID:2040 PID:9580
VID:0CCD PID:005A
VID:2304 PID:022C
VID:07CA PID:B808
VID:2040 PID:7060
VID:0413 PID:6F00
VID:1584 PID:6003
VID:185B PID:1E78
VID:07CA PID:A807
VID:2040 PID:7050
VID:2040 PID:9950
VID:2040 PID:9941
VID:10B8 PID:1E78
VID:10B8 PID:1E14
VID:2137 PID:0001
VID:0FD9 PID:002C
VID:2013 PID:0246
VID:1BA6 PID:0001
VID:07CA PID:F337
VID:07CA PID:0867
VID:07CA PID:A867
VID:07CA PID:0337
VID:07CA PID:1867
VID:07CA PID:B867
VID:07CA PID:A333
...
and many more as AF90xx are not listed. You need to send the command "modinfo "+ chipset model, to have the list supported, perhaps yours is on it... probably "modinfo af9015" will then tell you if yours is in the list.

Ok, if these vid:pid is not in your main product OpenPli 4.0 wIPTV, please tell me then in which image it is so I can use that in my boxes.

So for me it seems it's built-in the drivers (yours), check with the command as explained, send it and post back here the list of VID:PID you have back with telnet/SSH,

Admin

I hate to tell you, but this is above my knowlege to do this telnet stuff in my pc. Dongle is in one of the usb slot and send telnet command to it I really don´t know how to do that.

I will check, don't worry, I have few dongles here and will go thru them all and add all the VID:PID of the missing chipsets on the table/link I gave you. Will need some time ;o) naturally to do all this.

Admin

Chipset AF9005 :

VID:10B9 PID:6000
VID:0CCD PID:0055
VID:15A4 PID:9020

Chipset AF9015 :

VID:1F4D PID:9016
VID:07CA PID:850B
VID:0CCD PID:0099
VID:0CCD PID:0097
VID:07CA PID:815A
VID:1B80 PID:E39A
VID:1B80 PID:E383
VID:0413 PID:6A04
VID:1B80 PID:E402
VID:1B80 PID:E39D
VID:1B80 PID:C161
VID:1B80 PID:E400
VID:0458 PID:4012
VID:1B80 PID:C810
VID:1B80 PID:E397
VID:07CA PID:A805
VID:07CA PID:850A
VID:15A4 PID:901B
VID:1B80 PID:E395
VID:1B80 PID:E39B
VID:1B80 PID:E396
VID:1462 PID:8807
VID:07CA PID:A309
VID:10B9 PID:8000
VID:07CA PID:8150
VID:1462 PID:8801
VID:1AE7 PID:0381
VID:07CA PID:A815
VID:1B80 PID:C160
VID:0CCD PID:0069
VID:13D3 PID:3237
VID:13D3 PID:3226
VID:1B80 PID:E399
VID:2304 PID:022B
VID:0413 PID:6029
VID:15A4 PID:9016
VID:15A4 PID:9015

Chipset AF9035 :

VID:07CA PID:B835
VID:07CA PID:A835
VID:07CA PID:0825
VID:0CCD PID:00AA
VID:0CCD PID:0093
VID:15A4 PID:9035
VID:15A4 PID:1003
VID:15A4 PID:1002
VID:15A4 PID:1001
VID:15A4 PID:1000

Ok, so my dongle should work and it works many years with Nemesis 110r0 and sim2.10.

Now I need to start from scratch and come up with something. Thank you for your patience Admin.

Just for test, try the v21 version of the image (instead of v22), we never know, as some members prefer the v21 as the v22 look like to have some bugs.

Admin