12528 Members
237 Forums
7811 Topics
24004 Posts
Max Online: 9115 @ 08/24/24 07:30 PM
|
|
|
|
13 registered (Toysoft, Admin, tomash, OMEGA, Smokey, haki, bobot, karimkaki15, goode men, Franco89, raffsif1234, didond, gerolamo),
1490
Guests and
135
Spiders online. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
|
|
1
|
2
|
3
|
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
#18913 - 06/02/19 05:29 PM
Re: 50% Loading Display DM8000HD
[Re: deny]
|
VIP Japhar
newbie
Registered: 03/08/16
Posts: 45
|
I performed measurements of U2 and D12. Please confirm that I need to replace U2 (MP1484). thank you very much! 
|
|
Top
|
|
|
|
|
|
#18916 - 06/03/19 05:51 AM
Re: 50% Loading Display DM8000HD
[Re: deny]
|
VIPF Japhar
enthusiast
Registered: 03/08/15
Posts: 218
Loc: Netherlands
|
Only when this happens when the power supply failed when it's tested without the motherboard.
You could do this test also by disable the pin 3 wire between the psu and the motherboard.
When it's still failed as you have measured, then I would replace the ic, but check at least the diode if it's leaking before you do the other things.
Useless to say that you need to remove the diode, or at least one side from the pcb to test it with a multimeter on diode settings.
Or else, just replace the diode to see if it solves the issue.
_________________________
Doing nothing leads to nothing. ------------- Please note, for technical support ------------- Will be given here, or on the jb8a8f8 forum and I prefer it in English. Johnny B. Click on the banner if you like to go there.. 
|
|
Top
|
|
|
|
|
|
#18919 - 06/03/19 07:05 AM
Re: 50% Loading Display DM8000HD
[Re: Johnny_B]
|
VIP Japhar
newbie
Registered: 03/08/16
Posts: 45
|
I removed the external DVB-C tuner and the box came back on. I have redone the measurements, and they are the same (all measurements were taken with the motherboard connected to the power supply). How do I check the D12? The direct and reverse voltage on D12 is the same as on pin 3 on U2.
|
|
Top
|
|
|
|
|
|
#18920 - 06/03/19 09:28 AM
Re: 50% Loading Display DM8000HD
[Re: deny]
|
VIPF Japhar
enthusiast
Registered: 03/08/15
Posts: 218
Loc: Netherlands
|
See youtube, diode measurement multimeter
In any case, you must at least disconnect one side of the diode from the pcb to measure it correctly.
_________________________
Doing nothing leads to nothing. ------------- Please note, for technical support ------------- Will be given here, or on the jb8a8f8 forum and I prefer it in English. Johnny B. Click on the banner if you like to go there..
|
|
Top
|
|
|
|
|
|
|
Previous Topic
Index
