12528 Members
237 Forums
7811 Topics
24004 Posts
Max Online: 9115 @ 08/24/24 07:30 PM
|
|
|
|
13 registered (Toysoft, Admin, OMEGA, tomash, Smokey, haki, bobot, karimkaki15, goode men, Franco89, raffsif1234, didond, gerolamo),
1571
Guests and
146
Spiders online. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
|
|
1
|
2
|
3
|
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
#2332 - 08/12/15 12:45 PM
Sim 1.0 working, Sim Japhar-Ferrari and Sim2 not..
|
Japhar Member
Carpal Tunnel
Registered: 10/19/10
Posts: 9993
|
Sim 1.0 working, Sim Japhar-Ferrari and Sim2 not working... One of our members had a problem with his DM800HD, he was using an old Sim 1.0 on his box and wanted to switch to the newer images and so upgraded his Sim. None of the new Sims were working (with ->error message)... and we told him that most probably this was a problem on the motherboard (perhaps not fully supply of Power to the smartcard chip). He found out that the Sim 1.0 was working with a 2.2v, but when inserting the Japhar-Ferrari Sim or the Sim2 it was dropping at 1.5v... the result seems to be a Transistor to replace. See photos attached. Admin P.S.: More infos, in French, http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=3388#Post3388Image of Sim card holder / socket connections to Pads: 
_________________________
|
|
Top
|
|
|
|
|
|
#5694 - 02/11/16 10:31 AM
Re: Sim 1.0 working, Sim Japhar-Ferrari and Sim2 not..
[Re: Admin]
|
stranger
Registered: 02/01/16
Posts: 3
|
I have same problem can u please tell me which transistor and how please ?
Attachments
image5.jpg (199 downloads)image6.jpg (198 downloads)image7.jpg (197 downloads)
|
|
Top
|
|
|
|
|
|
#5701 - 02/12/16 12:53 AM
Re: Sim 1.0 working, Sim Japhar-Ferrari and Sim2 not..
[Re: Admin]
|
stranger
Registered: 02/01/16
Posts: 3
|
Dear Johnny,
I connect it like this is that fine but its still not working and i donot know why I connect it and it give me 5 volt but still not working please advise
Ahmed
Attachments
image1.jpg (201 downloads)image2.jpg (57 downloads)image3.jpg (198 downloads)image4.jpg (196 downloads)
|
|
Top
|
|
|
|
|
|
#5704 - 02/12/16 03:32 PM
Re: Sim 1.0 working, Sim Japhar-Ferrari and Sim2 not..
[Re: Ahmed Basher]
|
VIPF Japhar
enthusiast
Registered: 03/08/15
Posts: 218
Loc: Netherlands
|
The 5v switch for the Sim 5v pin 1 is feed from the Q8 center pin, the drain side. Check if the print track from the Q8 to the sim card holder is still intact. Next step is to measure the Q8, or to replace. That is, if the Q9 is working well, otherwise the Q8 will not be switched. I think check the values according my measurements at Ohm and diode measurements. See the image, Howto check the simcard circuit (Ohm measurement). Howto check the Q8 (Diode measurement). Here, Dm800hd simcard issues.
_________________________
Doing nothing leads to nothing. ------------- Please note, for technical support ------------- Will be given here, or on the jb8a8f8 forum and I prefer it in English. Johnny B. Click on the banner if you like to go there.. 
|
|
Top
|
|
|
|
|
|
|
Previous Topic
Index
