I am going crazy. Gave up on the 800se that one is somehow broken.
Bought 2 800 se V2. I have already a working V2 with Japhar sim.
So i flashed a new one with Japhar image, got no ca. Solderd in a sim card , no ca anymore so ok.
It will not boot to image, it will boot in flash mode, so i flashed image again. still it wil not boot to image it hangs on boot screen
Flashed a working image from the other one, nothing.

Regards
Ad

Did you tried the bad sector recovery and reset of Bios ?

BSR : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=3137#Post3137

Bios Reset : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=5234#Post5234

Admin

Thank you for the fast response !
Tried it .
No change .
Gonna try to connect the chip again .
Connected wires to the board so the sim holder can stay .
Perhaps the soldering of the sim holder not ok .

Ad

Yes, what you tell could be a possibility, as generally it freezes because it needs the Japhar Sim to compute calculations, perhaps not enough "power" (Amp) going to it ? Your wires are not too thin ? Or PSU problem ? Does the PSU works with the other box ?

TS

HELP please
Did not work with the wires .
I solderd the chip back
Result : second failed . so no boot file ?
Flashed it with DREAMUP and browser .file newnigma2-ipk-weekly-dm800sev2-17_10_2021
It works fine .
Got the chip out , solderd the sim holder in .
Flashed it with japhar flasher , and browser ,file openpli-enigma2-8.0star-dm800sev2_Japhar_v6_GStreamer_1.18.3_20210611
Result : second failed . so no boot file again ???
Could it be that one of the connections to the sim is faulty ? so it does not flash the boot file ?
Or does it flash nothing at all .
The solder points .
I solderd it 3 times so it must be a connection on the mother board .
The chip works fine so the connections there are ok .
Which connection could be the faulty one ???
And can i make a bypass from the chip solder points ?
Are all connections to the sim used ?
Got the sim out a working v2 box .
Can i check the connection points in the sim holder with a muti meter ?
How to check the points ? and what values should it be ?
Wich soder points of the chip ,correspond with the solder points of the sim .

I can get it working the the chip but want the Japhar sim !!
Thanks in advance

Ad Smits

I don't want to give up yet .

On point of the sim .above of the cut out , Does not solder wel .
Perhaps that one , if it it used

Ad

Did you tried on the other box v2, to see if the Japhar sim is OK on it ?

If it's an hardware problem, you can see at jb8a8f8.com

Admin

I have given up on this one .
Found some points to messure . all ok
It just does not see the sim . put in an old ferrari sim ,no difference
no , no ca aerror ,nothing at all .
Just second fail .
Put the chip back al works fine . so no hardware problem there

i have 3 japhar sims .

I have another v2 ( i have 3 one is ok ) that i want to do , just think about it
or i still want to try that one .

for now take some time out , it is very tiring this work .

Thanks
Ad

Tried the last V2 , same result , not working .
The first , some time ago worked .
I think a sim in a V2 does not work anymore .
Perhaps some firmware made a change , to block it .
Everything lookes ok but it won't boot .
Placing chip back and it works .
Sim is ok , works in the other box .

Ad

So you talk about using it on an original DM800HDse V2 box ?

There is two sets of Japhar drivers for the Original box. We had v6 and v6+ drivers (that are v5 upgraded to v6 compatibility). v6 drivers worked only on original boxes with Japhar Sim.

Admin