Hi,

Just got a new Japhar Sim and DM8000 keeps crashing since replacing it.
The screen goes black every few hours.

Image installed: OpenPLi 8.xStar 20221106 GSt 1.18.5 v6

I was using the Ferrari Sim up to this with the Blackhole image and had no issues with crashes.

Thanks for your post,

First of all, try to remove everything (HDD/CD-DVD Drive/Extra Tuners/Cards) to see if this goes OK without.

Flash the image but first do a bad sector recovery, see topic below, while you flash the image.

Sector recovery : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=3137#Post3137

Reset Bios : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=5234#Post5234

Try to flash the image below :
http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=24700#Post24700

Flash first the SSL84J, then reboot and flash the image above

SSL84J : http://www.ourdreambox.com/ubbthreads.ph...4J_DM8000HD.rar

TS

I tried all the steps above and installed the image you suggested.
I have SSL84J also installed.

I can't get pasted the boot screen for installing the image.
Every time I reboot it stops there.

If it stops there, I would bet your box could have some malfunctions on the PSU, did you removed all possible power consumptions addons (tuner boards, HDD, CD/DVD, smartcards, CI, etc).

If it's a clone, this is definitely a problem on them, after some years the PSU are not enough reliable and need to have some parts replaced.

PSU : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=1592#Post1592

Also try to install your old image you told that was working, with the Ferrari Sim, as the Ferrari images will work with a Japhar Sim. Just to see if you have the same issues.

Admin

I just reinstalled my old Blackhole image that was running on the Ferrari SIM.

It booted first go.

Try to install this image, also the boot is long as the DMM anti-clone security on the latest drivers we use is doing a lot of computation... so it would take few minutes to boot.

Flash the SSL84J, then reboot and flash the image (don't flash after any SSL on top of the image, the ssl is already built-in in the image).

If you still have problems, please post a foto of the LCD screen and where it is of the boot (screen of TV as well).

TS

-----------

DM8000HD : OpenPLi Develop Release 20221110 (v6)
openpli-enigma2-homebuild-develop-python3-dm8000-Japhar.nfi



- OpenPLi Develop by OpenPLi Team, November 10th 2022
- Python 3
- GStreamer 1.19.2
- AC3+/DDP/EAC3 support
- Japhar Sim Required

Download : https://mega.nz/file/ELZyHICb#VBRLQMoBqsAgoAwsd18Fj4ag7FF6pkFvdrjyKiHfU_o

Hi,

That's the one you said to try in your first reply above.

It won't go past the boot for installing the image after I install it.

I installed the latest japhar blackhole image and that also boots.

I there any chance there could be an issue with the openpli image.

There could be multiple reasons why it doesn't boot, this is the reason why it's important to know exactly what you have on the LCD screen of your DM8000HD when you think it stops booting, and that you flash the image at the end only and not after flash any other thing such as the SSL (as it's already built-in the image).

The image is working, it's the official image patched with Japhar Drivers and we done the backup of it, that is the image you flash.

If you want you can try the previous one, that is the Japhar build, the link is : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=24681#Post24681

TS

Boot sequence on LCD









The image was the last to be installed.



That's the image I opened this thread about.
The screen goes black every few hours.

If it shows an IP address, as I can see on the last LCD screen, at boot... its like if the button was pressed (UP/DOWN) or the boot data (like an autoexec.bat) was corrupted.

This STOP is requesting to flash an image (it shows the SSL software to upload the image) if you enter the IP address on your browser.

Try again the bad sector recovery flashing the image and to reset the BIOS.

TS