Trying for hours to solve the problem of Dreambox 800 hd (se) -Sunray sunshine.

It does not boot and when trying to flasg (mini flash) keep receiving led error "No Ca or image second failed.."

It has sim 2.10. Tried with Japhar nc3 .

When flashing with Japhar flasher (serial mode) it seems that image is written and loaded but when finished (with success) not booting again with the same error !!

Do not know that to do ( tried also with yassinov proggy NCF ver 3.0 and receive J45 cable error though cable connection to main computer verified and ok !)

Can anybody help solving ????

Did you tried the JapharFlasher ?

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=2012#Post2012

On the Sim2 boxes, the back button loads a Sim2 SSL, so it will work only if you have a sim2 in the box.

For the loading of the box, did you proceed as explained on the PDF posted ?

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=2283#Post2283

We had a similar problem with a DM800HD box, and it was staying at DM800HD on the DreamUp, nothing more and Johnny verdict was that the Flash chip was damaged.

Admin

Sunray box..
Mostly you have more success if you upload at least the boot loader with the browser.

Even better, Upload first the image file with the browser, do not reset, but go back one page with the browser and upload the boot loader.
After that you can turn off the box, and turn it back on.

Use the boot loader and image file that is suitable for your sim card.

Some info..
http://www.singapore-dreambox.com/how-to-flash-dm800-se-dm500hd-with-sunray-flashup-and-browser/

However, It could also be caused by the use of w7.
See this image to give some idea.
http://jb8a8f8.com/support/index.php?attachments/dm800se-display-status-jpg.5/

Thanks a lot for the replies.

I am doing everything "by the book".

Even tried "optiflasher" using com port and received a message to put the IP shown in the panel. But I receive no IP at the panel!!! .

It seems that I realy have a serious bootloader ( which is on board) problem and do not know how to solve it !!!

Please Try the JapharFlasher and let us know the result, as well as please put screenshots of the whole JapharFlasher window when it is stuck (attach with the "Switch to Full Reply Screen" reply box),

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=2012#Post2012

Thanks,

Admin

Dear all,

I have No problem with Japhar flesher. Using it I can flash any image but in vain because after image is flashed and I reboot the receiver is in the same condition eror.

I upload the stage where I am stuck using Optiflasher..

Regards,

Check to be sure that the sim is properly inserted in the box, and try to flash the SSL84 ALLSIM only.

Then try both Sim, Sim2 and Sim Japhar, and tell us what happens exactly on the LCD (Pleas post a photo of the LCD).

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=290#Post290

Also did you flashed activating the "Bad Sector Recovery" option ? It could be important. If you activate via Telnet on the IP of the bo and then you flash via the WebIf, you will see on the Web page appearing the bad sectors and log, copy/paste that text here.

Admin

Here attached the screen shots while trying to flash AllSim and then Image with bad sectors option repair...
Fell helpless... Alas..

I see some issues on your example images.

1. Use network is off
2. Local PC ip is different than the Select one
3. Remote (dreambox) ip is out of range of the 10.0.0.X network.
4. Based on your screenshots you use at least Windows 7 or higher.

But okay, on this way it will not succeed to flash the box.
The best way is to repair/flash the box with a windows Xp system, or what you also can try is to hold the front push button, switch the box on, hold the front push button until you see the ip on the oled display.

Use this ip in your browser to upload the image file and the boot loader.

Other method if present, same as above but than do it with the push button on the back.
This is a second option.

Needless to say that you need to connect your dreambox on your network and it must be a dhcp network.

What is the image you flashed ? What is the SSL in the box ? And What is the SSL of the image you want to flash ?

This happens generally when you have an old SSL on the box, and you want to flash the complete image... without going thru the SSL84 first then reboot and flash the full image then.

Admin